Why I'm comparing "direct" vs "assisted" instead of just listing specs
I run custom engraving orders — tumblers, wood signs, small metal tags — and I've been doing it for five years. In that time I've made (and documented) three expensive mistakes on the xTool S1 alone. Total damage: roughly $2,100 in scrapped stock and wasted marking spray. I now keep a one-page material checklist taped to the enclosure lid.
The spec sheet makes the S1 look like a single machine that just handles everything you throw at it. The shop floor says otherwise. On basically every material, there are really two workflows you can run:
- Direct — the machine and the material, nothing in between.
- Assisted — you add the rotary attachment, a coat of marking spray, masking tape, or a jig before the laser fires.
That difference isn't marketing. It's time, money, and whether the result is actually sellable. So this isn't a spec review. It's a straight comparison of where each workflow earns its keep. Four categories I get asked about constantly: steel, tumblers, wood, and glass/acrylic.
One clarification up front: I'm not a materials scientist, so I can't explain the chemistry of why marking spray bonds to stainless. What I can tell you is what produced sellable results in my shop and what ended up in the scrap bin.
1. Steel: "direct" is the trap
The most common thing I hear from people shopping a "steel laser cutter machine" is that they expect to cut steel. That's not what a diode laser does, and it isn't what the S1 does. The S1 marks metal — and even that requires help on bare stainless steel.
Direct on bare steel: You'll get a faint, inconsistent line at best. On polished stainless it's nearly invisible.
Assisted (marking spray or laser marking paper): This is how you actually get a crisp, dark, repeatable mark. You coat the surface, let it dry, run the job, then wash the residue off.
In 2022 I tried to engrave a batch of 40 stainless tumblers "direct" because I didn't want to pay for marking spray. I burned through three hours and about $400 in blanks before I admitted the marks wouldn't survive a single wash. The marking spray cost was around $30 for the whole batch. That's the kind of math that sticks with you.
The counterintuitive bit: on bare steel, going higher on power didn't help. It just made the line wider and uglier. The fix was the assist layer, not more watts.
My conclusion: For any bare stainless or aluminum part that needs a visible mark, treat marking spray as a required step, not an upgrade. The steel keyword is real, but the workflow is assisted every time.
2. Tumblers: rotary vs. flat bed
This is where the xTool S1 rotary attachment earns its price tag — and where it has its own learning curve.
Flat bed (direct): Works fine on flat stock. It does not work on a tapered tumbler. I tried it once in a hurry. The can wobbled, the engraving ran off-center, and I redid 12 units. Not ideal.
Rotary attachment: Required for anything cylindrical or tapered. But "required" doesn't mean "plug and play." You've got slipping (the tumbler wants to rotate on the roller), focus distance changes as the diameter changes, and on tapered cups you need to account for the coning or the design distorts.
A few settings habits that made the rotary usable for us:
- Run a low-power multiple-pass burn on powder-coated tumblers rather than one heavy pass. In my shop, 2–3 passes at moderate power beat a single aggressive pass almost every time on scrap and cleaning.
- Always test on the hidden bottom of the tumbler before running the visible face. One scrap cup is cheaper than one angry customer.
- Add a strip of masking tape over smooth stainless — it both helps the mark stay clean and reduces the cleanup.
Here's the part that surprised me: the xTool S1 rotary attachment isn't automatically the fastest path. For a single small flat-bottomed can, or for wide short items on a custom jig, the flat bed with a 3D-printed cradle was actually quicker end-to-end than mounting and aligning the rotary. Setup time on the rotary isn't zero.
My conclusion: Rotary for anything tapered, tall, or curved. Flat bed with a jig for wide, short, or one-off items — but test the jig before you trust it.
3. Wood: it depends on the finish, not the wood
The "how to engrave into wood" question usually gets answered wrong because people talk about wood species when the real variable is the finish.
Direct on raw, sanded wood: Predictable. Clean edges, consistent contrast. This is the easiest thing the S1 does well.
Direct on finished/coated wood: This is where it gets messy. A lacquer or poly coat can melt, bubble, and leave a hazy halo around the engraving. You'll also get inconsistent charring depending on how thick the coat is.
Assisted (masking tape over raw wood, or sanding off the finish first): Masking tape on raw wood reduces scorching around edges and makes cleanup easier. On finished wood, the honest answer is: sand the engraving area first, engrave, then spot-finish the engraved patch.
I lost a $120 batch of finished oak plaques early on because I engraved straight through a thick poly coat. The charring bled into the grain and there was no sanding it out without ruining the plaque. Lesson learned the hard way: test on the bottom of every new finished board.
My conclusion: Raw wood is a direct workflow. Finished wood is an assisted one — sand locally first, or accept the risk and test.
4. Glass and acrylic: coating and cast vs. extruded
Two comparisons get jammed together here, so let's separate them.
Glass — direct vs. coated: A diode laser on bare glass mostly passes through. Direct engraving gives you a frosted, inconsistent result. Coating the surface first (marking spray, or even a thin smear of dish soap and water that dries) produces a cleaner, whiter mark. It's an assisted workflow, full stop.
Acrylic — cast vs. extruded: This isn't a workflow choice, it's a material choice, but it matters more than your settings. Cast acrylic engraves to a crisp white and cuts cleanly. Extruded acrylic engraves hazy and melts at the edges. If you want sellable acrylic, buy cast. I learned that the expensive way on a $180 sheet of extruded.
My conclusion: Glass is assisted (coating required). Acrylic is a material-selection problem, not a settings problem — buy cast.
Which workflow should you actually use?
Looking back, the pattern is obvious, but it cost me a few hundred dollars to figure out. Here's the honest split:
- Bare stainless or aluminum → assisted (marking spray). No exceptions for visible results.
- Tapered or curved items → xTool S1 rotary attachment. Wide short flat-bottomed items → flat bed with a jig, if you've tested it.
- Raw sanded wood → direct. Finished wood → sand locally first (assisted).
- Glass → assisted (coating). Acrylic → cast only; the workflow is the same, the material does the work.
Two boundary conditions, because my shop isn't yours:
This worked for us, but we run custom small-batch orders with predictable test cycles. If you're a high-volume production shop doing one material all day, the calculus changes — you'll have a fixed setup that makes direct workflows viable at scale. And if you're a true one-off hobbyist, the "assisted" overhead per job might not be worth it for low-stakes practice pieces.
On the efficiency angle: documented settings win over raw speed every single time. When I started keeping a written settings log per material and per tumbler brand, our redo rate dropped from roughly one in five jobs to closer to one in twenty over about six months. That's not a machine upgrade. That's just not guessing anymore.
Bottom line
The xTool S1 is a solid diode engraver, but the "multi-material" label hides a real distinction: some materials engrave direct, and some need the rotary attachment or a coat of marking spray to produce sellable results. Treat the assisted workflows as required steps, not optional add-ons. And — because it's a Class 1 enclosed laser under FDA laser product rules (21 CFR 1040) — keep the lid and interlock working, and don't defeat them to save time. That's the one shortcut that isn't worth $30, ever.